2012-03-11

Keyboard Washing

Okay, so it's been a while. No matter.

So I have this good friend that had a few people dropping by for some of that good ol' alcohol, and some of it ended up in a keyboard. Happens all the time.

Instead of buying a new keyboard every new moon as spoiled brats would, we give it a good washing, right?

My friend has a G11, and incidentally I had one lying around. She lives a few hours drive away, so I took some pictures to show her how to proceed.




First off, start with a clean and cleared kitchen bench or table. Preferrably the kitchen bench - as you would then have electrical ground readily available. Keyboards are electronic devices and parts of them (the main circuit board) are sensitive to electrostatic discharges - which we avoid by discharging our body to ground prior to (preferrably while) touching the sensitive components. Ideally, you'd use a ground leash with an internal resistance to avoid a too rapid discharge of touched electronics. But that's not something most people have lying around, now, is it?

Now, if you're lucky, all you need to do is pop out the keys to wash (under) them. For this you'll be well off with a flat, wide screwdriver.


Insert the screwdriver vertically between the top and second top row, then bend it down towards the lower rows, and give it a slight twist.


This should make the key pop off (you might want to keep a cat nearby to catch any stray keys).


I'd advise you to hold a hand over the keys as you pop them out, and to start at the top row.


The larger keys have a metal wire to guide it, which can be easily removed with your fingers, or a pair of pliers. Pull straight out of retaining clips, one on each side. Wipe off them with a damp cloth and leave to dry.
Then just wipe with a fairly wet cloth underneath, and throw the keys in the dish washer (or in the sink with some of that mild detergent).
Put the guiding wires back into their retaining clips, and fold them down flush with the surface of the keyboard.


Then put all the keys in a cloth and shake them for a while to soak off some of the water, and leave them belly-up to dry for a few hours/over the night. Then stick'em back in.


My keyboard had English (US?) layout, so use your fantasy - or refer to the picture you took before popping the keys out (you did take a picture, didn't you?) - for their correct positions.




On the other hand, if you're not lucky... bring out your tools.

Most keyboards utilise at least one size of screws. The most usual sizes are Philips 2 (PH2). The G11 has four different kinds of screws, of sizes PH0, 1 and 2. Note that there is a difference between Pozidrive (PZ) and Philips (PH). You will be able to cross switch, but you're very likely to ruin the screwdriver. See wikipedia article on screw drives, Philips and Pozidriv (didn't know it was without 'e' at the end).



So for the G11 you will need:
* A flat, wide screwdriver (for the keys and bezel)
* Screwdrivers of sizes Philips 0, 1 and 2
* Thin pliers (or a large tweezer)
* Cups or jars for the screws


Start by unscrewing all the PH2 screws at the back of the keyboard.
Drop all screws in a jar so they don't disappear.


Now have a close look at the front bezel - or, rather, try to peer in between the bezel and the frame. I used an old membership card, but a flat screwdriver or a knife will work - but will leave dents. The bezel has been clipped onto the plastic frame in 11 places. Two on each side, three at the bottom, and four at the top. Use the flat screwdriver or other firm, thin object - to poke the clips off from their ledge. This is the trickiest part of the whole process, and also the part most likely to lead to destruction. Patience and good lighting is recommended. I've disassembled many keyboards for washing, and I've broken more of these clips than I've had holes in my teeth.


You can either push the clip itself off of the ledge, or push the ledge away from under the clip. Like I said, this is the trickiest part, and I haven't found a very good solution myself yet. Experiment. The clips don't seem to be important since the entire bezel is screwed onto the keyboard base anyway, so breaking them probably doesn't matter.

The four clips at the top shouldn't pose much of a problem if you're able to get the other seven (I haven't even bothered to indicate them, but they're between the play controls and the function keys).



Remove keys from the bezel.


When removing wires, note how they are snaking along. That is, notice how they are routed via various guiding slots in the plastic. This will help you replace the wires later to avoid them getting squeezed (possibly resulting in connection loss or short circuits).

If you have to remove the circuit board, make sure to discharge yourself to ground first by touching a bare metal sink or tap. Handle the circuit board along its edges (don't grab it like it was a chocolate bar).


Next, start unplugging the circuit board, and remove the ground screw . The connectors can be a bit tight, but try to wriggle them out. Avoid straining the wires if possible (try spread the strain evenly on all wires if you have to). The flat, flexible plastic connectors will need extra care as they are fragile. Use pliers and avoid making sharp bends and dents. Some of them have "ears" to pull at.


Unscrew all screws. The cover on the pressure switch assembly also has clips, so look for them and get them off like the others.

Remove any other pieces you need to from the keyboard base and wipe it clean with a damp cloth (or toss it in the dish washer).


The actual pressure switch assembly is made out of four parts; two flexible circuits with a spacer sheet between them, plus a bumpy silicone mat. The sheets are easily cleaned with a damp cloth, but can be sent through the dish washer (but they're thrown about a bit and can get stuck/block drain, etc).


The plastic parts (keys, bezel, frames and base) can generally be put in a dish washer. Paper labels are probably destroyed. Adhered stuff can come loose and possibly cover the drain in the machine, so should be carefully removed prior to washing.
Shake the parts to get rid of excess water, blow water out from corners, then soak up further excess with a dry cloth, and leave the parts to dry for a few hours/over the night.

Follow the procedure above in reverse to reassemble. Be careful, especially with the flexible plastic sheets and connectors. When fitting wires, make sure that they are not squeezed.